How To Remove A Bathtub And Replace With A Tile Youtube
If your bathtub is leaking, worn, cracked, or just looking tired, it might exist fourth dimension to upgrade to a new one. A standard bathtub replacement tin can be purchased at your local dwelling house center and installed by a plumbing professional. However, removing the sometime tub and installing its stand-in tin can be time-consuming and costly, so buy the best bathtub you can afford to ensure y'all won't take to repeat the process for another 15 or 20 years. And if you'd adopt to take a DIY route, we'll testify you how to remove the tub on your own in our pace-by-step guide to replacing a bathtub below.
Because yous're swapping out an existing tub, your options will be limited by the current tub'south dimensions, as well as the size of your bathroom's doorway. Before buying a new tub, you lot'll need to know the tub's exact width and length measurements and where the drain is placed (left, right, or center).
An cheap replacement tub may be narrower than the old tub. Many people find a narrow tub uncomfortable, and then be sure to consider comfort earlier you buy. Virtually tubs fit into a lx-inch opening, but some older ones can be longer. Measure out to make sure your replacement tub volition fit. Some spa or whirlpool tubs fit a standard tub opening, and installing one is not much more than work than installing a standard tub, although a spa or whirlpool needs to plug into a GFCI (ground fault circuit interrupter) electric receptacle.
Tips for Buying a New Bathtub
Materials matter when shopping for a new bathtub. Acrylic or fiberglass tubs are inexpensive, low-cal, and easy to install. Some have finishes that are fairly durable, but they can get dull in time. An enameled steel tub has a sturdier finish just lacks insulating backdrop, so bathwater will typically cool speedily. Enameled cast iron is the almost expensive and heaviest fabric just might be worth the cost because it retains a gleaming finish for decades, fills quietly, and keeps water warm the longest.
Generally, standard bathtubs feature decorative aprons on an exposed side(s) and are establish in white, biscuit, and cream, though other colors such as black, pastel blue, and pink finishes are available on midrange and pricier tubs. Rectangular tubs can feature rectangular, hourglass, or oval interiors, and then give each bathtub you're considering a exam run if possible. Lay down in the bathtub to check fit and comfort level. Are in that location contoured head and armrests, sideslip-resistant floors, and ample rims for holding toiletries and/or bathroom toys? Integrated seats, available on some midrange bathtubs, introduce added convenience while tubs with a curved apron wall supply extra bathing space.
Bathtub Toll Guide
The prices of standard bathtubs vary more past material than pattern. Here'south a look at the typical costs and the pros and cons associated with the most mutual types of standard bathtubs.
Enameled steel bathtubs range from $150 to $850. Less expensive and lighter in weight than cast atomic number 26, these tubs chip somewhat hands, can be slippery, allow water to cool quickly, and offer express colour choices.
Enameled cast-fe tubs range from $375 to $2,200. Available in a wide range of colors, these tubs are durable and retain heat, but they are also heavy and might crave additional structural back up.
Acrylic tubs range from $300 to $ii,000. Lightweight, fade-resistant, and available in many styles with integrated comfort features, acrylic tubs concur heat well when insulated but might show scratches.
Fiberglass/plastic composite tubs range from $250 to $800. Polyester gel coat finishes and fiberglass backing oft supported by wood or metal framing create a upkeep-friendly, lightweight tub in many styles.
Proprietary composite tubs range from $250 to $900. Americast past American Standard and UltraCast by Briggs are examples of materials that combine heavy-gauge steel, porcelain enamel, and resins to build bathtubs that offering all the benefits of cast iron at half the weight.
How to Remove an Erstwhile Bathtub
Removing the bathtub yourself isn't all that hard. Earlier you begin, measure the tub and make sure you'll be able to get it past other fixtures and out the door. Remove the sink or the toilet if they will be in the fashion. To protect the floor, cut and record pieces of plywood to the floor and encompass with a drop cloth. Then follow these steps on how to remove your old tub.
What Y'all Need
- Screwdriver
- Strainer wrench
- Pliers
- Pry bar
- Hammer
- Reciprocating saw
- Utility knife
- Crowbar
- 2x4s
Stride 1: Pull Out Bathtub Drain
From within the tub, unscrew and remove the overflow cover plate. If a drain assembly is attached to information technology, pull information technology out. (A drain assembly with a plunger is shown.) Unscrew and remove the mounting bracket if there is one.
Step ii: Disconnect Drain
To disconnect the drain, you might need to remove a screw or two and remove the strainer. You could also need to lift out a stopper and a rocker assembly. Employ a strainer wrench to remove the drain flange.
Step 3: Disconnect Waste-and-Overflow
From an admission console behind the tub or from below, disconnect the waste-and-overflow (WO) unit of measurement from the drain line. Depending on the installation, you might demand to unscrew a sideslip nut or loosen the screws on a no-hub coupling. If the parts are cemented plastic, you'll have to cutting through a pipe. Remove the WO unit from the tub. (You lot might non demand to remove the old WO unit of measurement if information technology will fit exactly on the new tub. Measure carefully.)
Footstep 4: Remove Tub Spout and Tiles
Remove the tub spout and remove the wall surface all around the tub to a height of near 8 inches. (If there are tub faucet handles, exit them in place if they are at least eight inches to a higher place the tub.) Use a flat pry bar or putty knife to pry off tiles. Cutting through drywall with a drywall saw. If the wall is plaster, employ a reciprocating saw, taking care not to cut into the studs. Pry off nails or unscrew screws.
Step 5: Pry Abroad Tub
Pry out or unscrew whatever nails or screws anchoring the tub flange to studs. Where the tub rests on the flooring, use a utility knife to cutting through the dewdrop of caulk if there is one. Utilise a crowbar to pry the tub an inch or then away from the back wall.
Step vi: Lift and Slide Tub
Unless the tub is an former-fashioned hook-foot or another blazon of stand-alone bathtub, information technology volition fit adequately tightly between studs on either side. That means you probably tin can't slide it out unless you cut away the wall surface on both sides. The best way is unremarkably to elevator the tub on 1 terminate. Pry up one end of the tub kickoff with a crowbar, so with 2x4s. Working with a helper, stand the tub upright and slide it out.
How to Install a New Bathtub
Once the old tub has been removed, you lot're ready to install the new one. Follow these stride-past-pace instructions to learn how to install a bathtub.
What You Demand
- Measuring tape
- Waste-and-overflow unit
- Ledger boards
- Drill
- Level
- Drain shoe and gasket
- Screws
- Overflow trim and flange
- Screwdriver
- Shoe tube
- Plumber's putty
- Strainer wrench
- Plastic putty knife
- New tub
- 2x4s
- Cement backerboard
- Tiles
- Adhesive
- Employ grout
- Silicone or tub-and-tile caulk
Pace 1: Bank check the Drain
Check the bleed and replace any damaged parts. Consult the manufacturer's literature and measure to brand sure the drain is in the correct location. Purchase a waste product-and-overflow unit ($33, The Abode Depot) and determine how you will connect information technology to the drain line. Screw ledger boards to the studs at the height recommended by the manufacturer. Ideally, the finish flooring fabric should run nether the tub.
Step 2: Dry out Fit Tubes
Working with the tub turned on its side, dry out-fit the overflow tube and the shoe. Make any necessary cuts, then make permanent connections. Place the gasket on the overflow flange, position it behind the overflow pigsty, and insert the linkage.
Step 3: Add the Overflow Trim
Within the tub, slip the screws into the overflow trim. Concord the overflow flange in place and hand-tighten one of the screws. Start the 2nd screw and tighten both with a screwdriver.
Step 4: Insert Shoe Tube
Insert the shoe tube into the opening in the overflow tube. Slip the other end into the drain hole.
Step 5: Spiral in Flange
Within the tub, place a rope of plumber's putty ($1, The Home Depot) under the strainer or drain flange. Hold the shoe with one hand while you lot screw in the flange. Terminate tightening with a strainer wrench. Clean away the squeezed-out putty with a plastic putty knife.
Pace half-dozen: Tilt in the Tub
Earlier tilting and moving the tub, plan the movement and then you avoid damaging the waste-and-overflow unit, which protrudes below the tub. Information technology might piece of work best to rest the tub on 2x4s part of the time. Move the tub into position with a helper. Y'all may have to tilt the tub. Slide it into the opening and gently lower the tub in place, using a helper to guide the overflow tube into the drain line if needed. Slide the drop material or any other protective cloth out from under the tub. Protect the tub interior.
Step 7: Check for Level
Check the tub for level; an out-of-level tub might non drain completely. Attach the tub to the studs according to the manufacturer's directions. You probably volition nail or screw through an acrylic tub flange. For a metal tub, bulldoze nails just above the flange.
Stride 8: Connect Waste-and-Overflow Slice
Working from behind or below, connect the waste material-and-overflow tailpiece to the drain line. To test for leaks, close the stopper and fill the tub. Open the stopper; picket and feel for any sign of wetness.
Stride 9: Add together Tile Around Bathtub
To fill the gap above the tub, cut and install strips of cement backerboard, which is more wet-resistant than green drywall. Install tiles to fit, let the adhesive to ready for a day, and use grout. Apply silicone or tub-and-tile caulk where the tiles run across the tub.
Source: https://www.bhg.com/bathroom/shower-bath/replace-a-bathtub/
Posted by: lenoxnembee.blogspot.com
0 Response to "How To Remove A Bathtub And Replace With A Tile Youtube"
Post a Comment